[jadmin] Jabber Questions

[Jeff Garner]

Karim Malhas wrote:

>-----BEGIN PGP SIGNED MESSAGE-----
>Hash: SHA1
>
>Hello Frank,
>
>  
>
>>Here's my question. Is there a way to get my jabber server here in
>>Seattle, to communicate with the jabber server in England to interact
>>with the users on the original jabber server?
>>    
>>
>
>Assuming that both servers are on the public Internet, have routable DNS
>addresses and no firewalls restricting their communication, it's quite
>simple:
>
>Just let the users in Seattle add the users from England to their roster
>
>HTH
>
>Karim
>
>
>- --
>Use GnuPG Encryption. My key: http://karim.malhas.de/karim.asc
>-----BEGIN PGP SIGNATURE-----
>Version: GnuPG v1.4.3 (GNU/Linux)
>
>iQIVAwUBRL3W8qX6AibVDljRAQJLZg//TDkgulWuIuX4yadClZCu/K8lmLSrskFU
>AyUyfWcAEUZAJhtEe74Q1XxpkTYdgB5LbPLWfAYeIhLRpyzIIDiVtGeLXdr7NC5C
>Bl41Kx8GDwMWsoXGNv9oDSyqPtQa3P39e/0zD9tYZgcnXRuAY1zU1VbfX1DyeW3l
>U4JHyV6frzaU50gATPReLbst+P7No8GJg03BhnpGfYInwZRC7pQZlouBN1jqcI5m
>6S7ywZtk878sLQcFL8Imn6+VWTB30YG+6dgQm32vEJaHku3FZ4y8Ys0zzTRbIkB1
>TYZpv2K+74S+eXWcCl70fIgYk0BkFU/PIBTDlOvbLaxq7o5g3N5oaF2Lm5BKfZwS
>LxRlxcYz3V/WcwioZXpUPHOf4JlSfiMub25gigFrKMaQhX2WzkPlJI4FLLrK+z0J
>UbwpZEIxW7w64OarC2hSyExvrgs8LBQrZLLPSHYOxNVp9WrK6PTKBDimxE7eq7RE
>tUpzKRMioBOsFBzUTVrPfcb0NMfX5/aHqs5zThXh6qjtkeMZ0IkOXB6cdsx9SMqY
>uid4PqS8z83mnijGpaEtFkEcNQ2vVbYhq0cWZPK+1WTW/VnbI+jUHNpj13U60hUf
>E9v77sRkMz9uw7Zn9cM1mQye6BBj9F6EfR9przfsg3TXJUk8spsrV1ncpZ9rLDU6
>OY1IhB7QC8Y=
>=7Mrx
>-----END PGP SIGNATURE-----
>_______________________________________________
>jadmin mailing list
>jadmin at jabber.org
>http://mail.jabber.org/mailman/listinfo/jadmin
>FAQ: http://www.jabber.org/about/jadminfaq.shtml
>_______________________________________________
>
>_____________________________________________________________________________
>Scanned by Sanmina-SCI eShield _____________________________________________________________________________
>
>  
>
Frank,
    I think something that Karim left out is important.  In Wildfire, go 
into the admin console, under the sessions tab, select server sessions 
on the left hot links, and select remote server settings.  on this page 
setup the information to connect to the server in England.  Whoever the 
admin in England is will have to also set his S2S config to point 
towards your server as well, and of course you need to agree on a shared 
key.  If the server in England is also Wildfire (a good choice by the 
way), both of these servers can be communicating in less  that 15 
minutes.  Check out the Forums at jivesoftware.org for specifics on 
Wildfire. 

Regards,

-- 
Jeff Garner
Network Administrator
Sanmina-SCI, Allen Texas
469.675.2441 <office>
972.768.5913 <cell>
jeff.garner at sanmina-sci.com



CONFIDENTIALITY
This e-mail message and any attachments thereto, is intended only for use by the addressee(s) named herein and may contain legally privileged and/or confidential information. If you are not the intended recipient of this e-mail message, you are hereby notified that any dissemination, distribution or copying of this e-mail message, and any attachments thereto, is strictly prohibited.  If you have received this e-mail message in error, please immediately notify the sender and permanently delete the original and any copies of this email and any prints thereof.
ABSENT AN EXPRESS STATEMENT TO THE CONTRARY HEREINABOVE, THIS E-MAIL IS NOT INTENDED AS A SUBSTITUTE FOR A WRITING.  Notwithstanding the Uniform Electronic Transactions Act or the applicability of any other law of similar substance and effect, absent an express statement to the contrary hereinabove, this e-mail message its contents, and any attachments hereto are not intended to represent an offer or acceptance to enter into a contract and are not otherwise intended to bind the sender, Sanmina-SCI Corporation (or any of its subsidiaries), or any other person or entity.
_____________________________________________________________________________
Scanned by Sanmina-SCI eShield  _____________________________________________________________________________